512 BBI with 512 M crank and Ti rods.
| Attachments: |
|
IMG_1579.JPG [ 2.19 MiB | Viewed 34525 times ] |
| gemellocattivo.com http://gemellocattivo.com/forum/ |
|
| Stuff I work on. http://gemellocattivo.com/forum/viewtopic.php?f=2&t=22 |
Page 1 of 2 |
| Author: | MerlinTech [ Fri Jan 09, 2015 8:15 am ] | ||
| Post subject: | Stuff I work on. | ||
512 BBI with 512 M crank and Ti rods.
|
|||
| Author: | mk e [ Fri Jan 09, 2015 8:48 am ] |
| Post subject: | Re: Stuff I work on. |
very pretty! What's the difference between a 512BBi crank and a 512M crank? |
|
| Author: | MerlinTech [ Fri Jan 09, 2015 9:13 am ] |
| Post subject: | Re: Stuff I work on. |
The M crank is like a 355 cut and drilled everywhere to make it light. I had to machine down the snout and make a special key so the standard BBI pulley and gears fit. Everything else was the same. |
|
| Author: | mk e [ Fri Jan 09, 2015 9:19 am ] |
| Post subject: | Re: Stuff I work on. |
Are there other hop-ups in the engine or planned? Generally when someone goes to the bother of a light crank and Ti rods they've got a plan to add rpm and hp 
|
|
| Author: | MerlinTech [ Tue Jan 13, 2015 8:13 am ] |
| Post subject: | Re: Stuff I work on. |
Pistons, cams and valves. We kept it mild because of stock injection. |
|
| Author: | mk e [ Tue Jan 13, 2015 8:20 am ] |
| Post subject: | Re: Stuff I work on. |
FoaTech wrote: Pistons, cams and valves. We kept it mild because of stock injection. If it's of any interest to you a guy on my open source ECU forum claims to have a way to use an ECU to control CIS systems. The full writeup is on the Pelican parts forum I think but but he posted and updates basics here: http://open5xxxecu.org/viewtopic.php?f=61&t=93 |
|
| Author: | MerlinTech [ Thu Jan 15, 2015 11:17 am ] |
| Post subject: | Re: Stuff I work on. |
I have seen the electronic controlled regulator for CIS. It uses an injector to regulate the pressure. I have not heard anything bad about it, but my issue is not getting to far off base and get the meter pulsing and causing all kind of head aches. Last I checked they are $650 and we need two for the Boxer. Larry Fletcher @ Flowtech set up our regulators and dist. head and they work really well. |
|
| Author: | a1exander [ Thu Jan 15, 2015 2:26 pm ] |
| Post subject: | Re: Stuff I work on. |
That assembly really looks magnificent. Well done to you. |
|
| Author: | MerlinTech [ Thu Jan 15, 2015 3:12 pm ] |
| Post subject: | Re: Stuff I work on. |
a1exander wrote: That assembly really looks magnificent. Well done to you. Thank you |
|
| Author: | MerlinTech [ Thu Jan 15, 2015 3:20 pm ] | ||
| Post subject: | Re: Stuff I work on. | ||
I do 'Merican stuff too. 383 aluminum head stroker with all roller top end.
|
|||
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|